22:24 | dmj_nova | okay, back :)
| |
22:24 | Bertl | wb :)
| |
22:28 | Bertl | btw, I uploaded an annotated package description file for the zedboard (which contains the pin to peripherial mappings)
| |
22:28 | Bertl | http://vserver.13thfloor.at/Stuff/AXIOM/xc7z020clg484_zedboard.txt
| |
22:28 | Bertl | it isn't complete yet, but it has most of the required info to know what each pin does
| |
22:40 | dmj_nova | okay, I'm in minicom now
| |
22:41 | dmj_nova | hmm
| |
22:41 | Bertl | when you power on the board, you should get a few messages
| |
22:41 | Bertl | like the u-boot revision, and in/out information
| |
22:42 | Bertl | then a message stating to 'hit a key to stop autoboot' and a counter
| |
22:43 | Bertl | that's where you interrupt and end up in the u-boot command shell
| |
22:44 | dmj_nova | hmm...not actually getting any signal from uart on boot
| |
22:45 | dmj_nova | wait, there's no /dev/ACM0
| |
22:45 | Bertl | did you copy the minirc.ACM0 to your /etc (or wherever your minicom puts its config files)?
| |
22:45 | Bertl | the device will be named /dev/ttyACM0
| |
22:48 | dmj_nova | okay, now we're in business
| |
22:49 | Bertl | :)
| |
22:49 | dmj_nova | bootp -> Unknown command
| |
22:49 | dmj_nova | nevermind
| |
22:51 | Bertl | did you get an ip?
| |
22:54 | dmj_nova | hmm...it seems to be looping
| |
22:56 | Bertl | pastebin the output please
| |
22:59 | dmj_nova | oh, never copied the boot.bin to the sd card
| |
22:59 | Bertl | yeah, kind of expected that, doesn't matter
| |
22:59 | Bertl | what's the output you get from bootp?
| |
23:00 | dmj_nova | http://paste.ubuntu.com/5809311/
| |
23:01 | Bertl | hmm, okay, that's good and bad
| |
23:01 | Bertl | actually it means that nothing is answering the bootp request
| |
23:01 | dmj_nova | left the channel | |
23:02 | dmj_nova | joined the channel | |
23:02 | Bertl | actually it means that nothing is answering the bootp request
| |
23:02 | Bertl | i.e. your router doesn't seem to care, or the board is not properly connected (network)
| |
23:02 | Bertl | so, assuming that the board is properly connected (leds on the etherjack should be on)
| |
23:02 | Bertl | you have two choices now:
| |
23:03 | Bertl | 1) pick a static IP ignoring the router
| |
23:03 | Bertl | 2) setup dhcpd on your dev system to answer the bootp requests
| |
23:04 | Bertl | in the first case, you just need to tell me the IP you picked, in the second, you can use the procedure I already outlined to assign the IP dynamically
| |
23:04 | Bertl | (which could even be on a separate network, e.g. 192.168.2.0/24
| |
23:04 | Bertl | )
| |
23:05 | Bertl | I'm going to solder an LM75 to a header now to test the I2C interface, will take a few minutes, let me know what you decide to do ...
| |
23:51 | Bertl | back now ... took me some time to find my hot-glue
| |
23:52 | Bertl | did you figure out how you want to proceed and/or what IP you want to use for the zedboard?
| |
06:05 | dmj_nova1 | joined the channel | |
06:09 | dmj_nova | left the channel | |
09:58 | Bertl | morning folks!
| |
11:16 | Bertl | \o/ i2c via PS controller, routed via PL to PMOD JB1 works!
| |
11:44 | Bertl | off for now .. bbl
| |
13:33 | jucar1 | changed nick to: jucar
| |
20:49 | jucar1 | joined the channel | |
20:51 | jucar | left the channel |