| 02:04 | fredy | left the channel |
| 02:06 | fredy__ | joined the channel |
| 02:06 | RexOrCine|away | left the channel |
| 02:11 | RexOrCine|away | joined the channel |
| 02:12 | intrac | left the channel |
| 02:13 | intrac | joined the channel |
| 04:48 | Bertl | off to bed now ... have a good one everyone!
|
| 04:48 | Bertl | changed nick to: Bertl_zZ
|
| 07:00 | mumptai | joined the channel |
| 07:30 | se6ast1an | good day
|
| 08:42 | mumptai | left the channel |
| 09:27 | BAndiT1983|away | changed nick to: BAndiT1983
|
| 11:10 | earabul | joined the channel |
| 12:13 | BAndiT1983 | changed nick to: BAndiT1983|away
|
| 12:15 | earabul | left the channel |
| 12:48 | Bertl_zZ | changed nick to: Bertl
|
| 12:48 | Bertl | morning folks!
|
| 13:02 | illwieckz | joined the channel |
| 15:28 | mumptai | joined the channel |
| 15:52 | Dest123 | joined the channel |
| 16:59 | vup | Bertl: BAndiT1983: I finally uploaded the pic stuff if you want to take a look: https://github.com/apertus-open-source-cinema/pic32mz-no-xc32
|
| 17:00 | vup | BAndiT1983: if you want to play around with the interrupt stuff, the points I wrote in the ISRs section might be interesting to look at
|
| 17:00 | vup | also just testing the current state on hardware, maybe it just works now? :)
|
| 17:03 | Bertl | should I swap out the pickit for testing on the remote setup?
|
| 17:05 | vup | I wont have time to do any testing today...
|
| 17:05 | Bertl | okay, then please ping me when you want to test this and I'll do it then
|
| 17:06 | Bertl | I have both devices here at hand so it can be done quickly
|
| 17:12 | vup | Sure, sounds good
|
| 17:52 | Bertl | off for now ... bbl
|
| 17:52 | Bertl | changed nick to: Bertl_oO
|
| 17:56 | Dest123 | left the channel |
| 18:17 | BAndiT1983|away | changed nick to: BAndiT1983
|
| 18:18 | BAndiT1983 | great! will check a bit later
|
| 18:18 | BAndiT1983 | ah, now i see that you generate the entries for ISR and config, nice!
|
| 18:20 | BAndiT1983 | in my tests i could reuse the parts from DFP, at least to avoid XC32 as far as possible, also startup code is there, as the license thing is a bit tricky
|
| 18:26 | BAndiT1983 | changed nick to: BAndiT1983|away
|
| 18:37 | BAndiT1983|away | changed nick to: BAndiT1983
|
| 18:42 | illwieckz | left the channel |
| 18:54 | illwieckz | joined the channel |
| 20:43 | vup | as far as I can tell the license allows redistribution with modification as long as the copyright notice is kept
|
| 20:43 | vup | I also reuse stuff from the DFP (or rather I copied them from a xc32 installation, but the files seem to match)
|
| 20:45 | BAndiT1983 | have not compiled yet, just checked the repo so far, will test in a moment
|
| 20:45 | BAndiT1983 | or do you have already pre-built HEX? then i could flash it to the board
|
| 20:47 | vup | https://files.niemo.de/usb.hex
|
| 20:47 | vup | https://files.niemo.de/lcd.hex
|
| 20:48 | BAndiT1983 | thanks
|
| 20:50 | BAndiT1983 | lcd.hex stays black
|
| 20:50 | vup | :(
|
| 20:51 | BAndiT1983 | usb.hex is also not running, usually i would see UART pouring in or /dev/ttyAMC0
|
| 20:52 | BAndiT1983 | will check what's going on there, do you still have the ELF files?
|
| 20:52 | vup | yep
|
| 20:53 | vup | just replace hex with elf in the link
|
| 20:53 | BAndiT1983 | ah ok, thanks
|
| 21:04 | BAndiT1983 | changed nick to: BAndiT1983|away
|
| 21:23 | RexOrCine | left the channel |
| 21:23 | RexOrCine1 | joined the channel |
| 22:42 | mumptai | left the channel |
| 22:45 | aombk | left the channel |
| 22:48 | aombk | joined the channel |
| 22:51 | intrac | left the channel |
| 22:52 | intrac | joined the channel |