10:31 | Guest18 | joined the channel | |
10:34 | Guest18 | Hey any chance of working with Sony to license this image sensor https://image-sensors-world.blogspot.com/2021/02/isscc-2021-sony-501mp-full-frame-sensor.html?m=1 from what I understand, it has higher image quality, because more columns have their own independent ADCs.
| |
10:36 | Bertl | Guest18: go ahead and ask them whether they are interested in releasing documentation for the sensor
| |
10:36 | sugarbeet | left the channel | |
10:37 | sugarbeet | joined the channel | |
10:39 | Guest18 | Well thats the point anyone who licenses it surely gets documentation? what about Kodak? are they as forthcoming?
| |
10:41 | Guest18 | left the channel | |
12:17 | max_bxl | joined the channel | |
12:18 | max_bxl | hello everyone !
| |
12:18 | max_bxl | (small) axiom club here !
| |
12:21 | Bertl | hey
| |
12:24 | se6astian_ | hi maxme, great you are hacking again!
| |
12:36 | max_bxl | =p
| |
12:37 | max_bxl | to be sure : the green LED on the MicroZED is telling us that the board is powered and the red LED is telling us that the OS is loaded
| |
12:51 | dos | left the channel | |
12:51 | dos | joined the channel | |
13:14 | max_bxl | where should I add this information (red/green LED) ? there : https://wiki.apertus.org/index.php?title=AXIOM_Beta/Manual#Operating_Basics ?
| |
13:21 | Bertl | the green LED is directly conencted to the MicroZed Power
| |
13:21 | Bertl | the red LED is controlled by the PS and the blue LED by the PL
| |
13:21 | Bertl | by default, the red LED shows a heart-beat pattern if all is running fine on the PS (Linux) side
| |
13:21 | se6astian_ | maxime, yes good place
| |
13:22 | Bertl | if the red LED is permanently ON, chances are good that the SD card is bad/missing and the MicroZed does not boot
| |
13:24 | max_bxl | yep ! actually the red LED wasn't even blinking, so I flashed a new card.
| |
13:25 | max_bxl | here's the content of axiom_rf_sel.py : https://pastebin.com/aYuXWKNj
| |
13:27 | se6astian_ | maxime btw would you be so kind and reply to *email address removed*
| |
13:27 | se6astian_ | he wrote to us in french
| |
13:27 | se6astian_ | to team
| |
13:30 | max_bxl | yep, I just saw, I was about to ask what to answer (he is basically wanting to know if there's a camera to sell) → I should explain that it's now "only" for developpers/makers (and not DOP/filmmakers) right ?
| |
13:33 | Bertl | max_bxl: please remind me what the issue was (it has been to long that I can remember :)
| |
13:34 | Bertl | (at least I presume that there is an issue ;)
| |
13:38 | max_bxl | yep ! it was a python error message at the end of the axiom_start.sh → https://pastebin.com/qB8qt1CS
| |
13:39 | max_bxl | se6astian said it might be related to https://github.com/apertus-open-source-cinema/axiom-firmware/issues/179
| |
13:39 | Bertl | and what is the version of your power board?
| |
13:40 | max_bxl | 29 (and not 30)
| |
13:40 | Bertl | okay, let's try to run the following then:
| |
13:41 | Bertl | pip3 install smbus-cffi
| |
13:41 | Bertl | and after that, rerun 'axiom_rf_sel.py A' and see what power board version it assumes
| |
13:49 | max_bxl | restarting the beta now (I double checked the power board version)
| |
13:49 | se6astian_ | yes, please tell him what we offer currently and ask about his application with the camera
| |
13:51 | max_bxl | assuming power board version 0.30*
| |
13:51 | max_bxl | without £
| |
13:51 | max_bxl | without *
| |
13:55 | max_bxl | se6astian_ done
| |
14:06 | max_bxl | Bertl I'll need to go in 10mn, is there something I can do now ? or should we upgrade the power board ?
| |
14:16 | max_bxl | left the channel | |
14:16 | Bertl | I think this is a problem with the used firmware, I presume it was not tested on older boards
| |
14:32 | Bertl | and yes, it might be related to issue #179
| |
14:32 | Bertl | probably best to arrange a remote session where we can connect to the camera
|